Go Back   GeekChat! > ELECTRIC GUITAR > Guitars

Reply

Share/Bookmark

 
LinkBack Thread Tools Display Modes
  #1  
Old 09.28.08, 10:21 AM
Registered User
 
Join Date: Nov 2007
Posts: 564
thevisionseeker is an unknown quantity at this point
How to wire Active & Passive pickups together?

I need to know how to wire up 2 humbuckers (1 Passive/1 Active) with a 3 way toggle, 2 volume, and 2 tone controls. Also possibly adding a killswitch. Anyone know how to run this properly?

I know there is a output difference but it doesnt matter for what I'm doing.
__________________
"All the world's a cage and we are animals knocking on the glass." - ETID
Reply With Quote


  #2  
Old 09.28.08, 12:35 PM
iaresee's Avatar
Registered User
 
Join Date: Sep 2006
Location: Here
Posts: 3,861
iaresee is on a distinguished road
From EMG's support page:

Q: Can I mix EMG's with passive pickups?

It is possible to mix EMG's with passive pickups. There are three possible wiring configurations; one is better than the other two.

Use the high impedance (250K-500K) volume and tone controls. The problem is that the high impedance controls act more like a switch to the EMG's. The passive pickups, however, will work fine. If you have a guitar with two pickups and two volume pots, with a three-way switch, there is another alternative. Use the 25K pots for the EMG, and the 250K pots for the passive pickup. This way you can use one or the other with no adverse affects, but with the switch in the middle position the passive pickup will have reduced gain and response.

Use the low-impedance (25K) volume and tone controls provided with the EMG's. The problem here is that the passive pickups will suffer a reduction in gain and loss of high-frequency response.

This is the best alternative. Install an EMG-PA-2 on the passive pickups. There are two benefits to doing this. With the trimpot on the PA-2, you can adjust the gain of the passive pickups to match the EMG's. The PA-2 acts as an impedance matching device so you can use the low-impedance EMG controls (25K) without affecting the tone of the passive pickups. You will also be able to use other EMG accessory circuits such as the SPC, RPC, EXB, EXG, etc. For this application, we recommend ordering the PA-2 without the switch for easy installation on the inside of a guitar.
__________________
- IAN C. -
Rig: PRS | Schecter USA | Gibson | Axe-Fx II | empress effects
Beta tester: Fractal Audio | empress effects
Reply With Quote
  #3  
Old 09.29.08, 7:24 AM
Registered User
 
Join Date: Nov 2007
Posts: 564
thevisionseeker is an unknown quantity at this point
Appreciate it. I've read this before and know there is a difference because I used to have this wired up before and it was amazing besides the toggle switch making noise due to the impedance difference but now I'm not worrying about that since I have a JCM 600 which I can EQ the 2 channels seperatly.

I just need a diagram of how to wire this all correctly.
__________________
"All the world's a cage and we are animals knocking on the glass." - ETID
Reply With Quote
  #4  
Old 09.29.08, 7:57 AM
iaresee's Avatar
Registered User
 
Join Date: Sep 2006
Location: Here
Posts: 3,861
iaresee is on a distinguished road
Quote:
Originally posted by thevisionseeker
I just need a diagram of how to wire this all correctly.
Follow this: http://www.seymourduncan.com/support...ic=2h_2v_2t_3w

And sub in EMG's recommended tone and volume pot values for the active pickup.

For a kill switch you want to add a SPST momentary switch on the line that goes from the 3-way to the hot tip on the jack.
__________________
- IAN C. -
Rig: PRS | Schecter USA | Gibson | Axe-Fx II | empress effects
Beta tester: Fractal Audio | empress effects
Reply With Quote
  #5  
Old 09.29.08, 9:08 AM
Registered User
 
Join Date: Nov 2007
Posts: 564
thevisionseeker is an unknown quantity at this point
ok ya that's how I've been wiring it up so far. Not done yet (shoule be tonight) but I was wrong about the killswitch so I'll rewire that. Thanks
__________________
"All the world's a cage and we are animals knocking on the glass." - ETID
Reply With Quote
  #6  
Old 09.29.08, 10:39 AM
asatbluesboy's Avatar
Registered User
 
Join Date: Dec 2005
Location: Brasil
Posts: 4,728
Blog Entries: 2
asatbluesboy is on a distinguished road
Quote:
Originally posted by iaresee
For a kill switch you want to add a SPST momentary switch on the line that goes from the 3-way to the hot tip on the jack.
Actually, an SPST wired between the tip and ring on the jack. It prevents that “disconnected cable� sound.
__________________
crew

Quote:
Originally posted by pop_n_fresh
The thought of EMGs on a Jag makes me vomit a little.

Originally posted by paradeblonde
Beep beeeep beeeeeeeeeep beeeeeeeeeeeeeeeeep BEEEEEEEEEEEEEEEPPPPPPPPP
Selling BOSS FW-3. I live in Brazil, mind you, so prepare yourself for $30-ish for shipping and waiting. Local pickup available, along with beautiful beaches and cheap bitches.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 11:47 PM.


Powered by vBulletin
Copyright ©2000 - 2014 | Jelsoft Enterprises Ltd.
SEO by vBSEO
©1993 - 2014 GuitarGeek | All Rights Reserved